JEGS 513003 Intake Manifold for 1955-1986 Small Block Chevy 265-283-302-327-350-400
Highlighted Features
- 1955-1986 Small Block
- Dual...
- 4-BBL Square Bore 4150/4160 Mounting
- Idle to 5500...
- Cast...
Features
Information
- Best Choice - #1 Best Intake Manifold For Chevy 327
- Checked on 07/10/2024
- Based on 43 Reviews
TYFYB Aluminum Satin Intake Manifold For Small Block Chevy SBC 305 327 350 400 1957-1986 1500-6500 RPM
Highlighted Features
- Intake gaskets with 1.23" wide x 1.99" tall port holes;Material:Aluminum;Bolt Hole Pattern:5.160" x
- Carburetor Flange Type:4-Barrel Square Bore;Power range is 1500-6500
- Aluminum intake is a dual plane, 180° street manifold designed to be used with Holley, Carter AFB or Edelbrock square flange
- Power comparable to single plane manifolds yet retains throttle response/driveability of a dual
- Fitment:Fits 1957-86 SBC Chevy engine
Features
Information
- Best Choice - #2 Best Intake Manifold For Chevy 327
- Checked on 07/10/2024
- Based on 43 Reviews
Aluminum Small Block Chevy SBC Intake Manifold Vortec Dual Plane 350 383 327 1997-up Idle-6500 RPM
Highlighted Features
- Engine Make/Size:Chevy Small Block (350,383
- Intake Style:Dual plane
- RPM Range: Idle-6,500
- Intake Material: Aluminum
- Ship from United States
Features
Information
- Best Choice - #3 Best Intake Manifold For Chevy 327
- Checked on 07/10/2024
- Based on 18 Reviews
ICT Billet 350 Chevy SBC Intake Manifold Flange Bolt Set Standard 3/8" Thread LT1 5.7L Compatible with Chevrolet Small Block V8 305 327 350 383 5.0L Eight Cylinder Long Water Pump 551653
Highlighted Features
- If you're needing to replace your old rusty intake bolts to go with your clean intake manifold, this bolt set will get you back on the
- These bolts will fit a Small Block Chevy up to 1997, including the
- Made in Wichita, Kansas from aerospace grade, USA produced billet
- We include 12 bolts in the set, so you'll have everything to get the job
- These bolts are a standard 3/8" coarse thread. Be sure to check your existing bolts and cylinder heads for matching
Features
Information
- Best Choice - #4 Best Intake Manifold For Chevy 327
- Checked on 07/10/2024
- Based on 40 Reviews
JEGS Small Block Chevy 1955-1986 Intake Manifold | Non-EGR Design | Idle - 5500 RPM Power Range | Polished Aluminum | Square Bore/Spread Bore Carburetor Mounting Pad
Highlighted Features
- IMPROVE ENGINE PERFORMANCE AND HORSEPOWER with this higher flowing intake manifold compared to a stock cast iron
- DESIGNED TO FIT WITH POPULAR AFTERMARKET SPREAD BORE AND SQUARE BORE 4150 CARBURETORS including Edelbrock, Holley, Quickfuel, Proform, Rochester Quadrajet, and
- FITS GM AND CHEVROLET CYLINDER HEADS from 1955 through
- IDLE TO 5500 RPM POWER BAND for street or mild race
- FABRICATED FROM CAST ALUMINUM for weight savings and improved performance and polished for great looks under the
Features
Information
- Best Choice - #5 Best Intake Manifold For Chevy 327
- Checked on 07/10/2024
- Based on 85 Reviews
SBC Chevy Fel Pro 1205 Intake Manifold Gasket 327 350 400 Performance (Stock/Small Race Port)
Highlighted Features
- Intake gaskets Only! No end
Features
Information
- Best Choice - #6 Best Intake Manifold For Chevy 327
- Checked on 07/10/2024
- Based on 61 Reviews
Aluminum Intake Manifold Compatible with 1957-1986 Chevy SBC 305 327 350 400 1500 to 6500 Rpm Assault Racing Products
Highlighted Features
- Aluminum intake is a dual plane, 180° street manifold designed to be used with Holley, Carter AFB or Edelbrock square flange
- Power range is 1500-6500 RPM,Larger-than-stock plenum and runners complements other
- Supports larger engines & enhances RPM potential,Power comparable to single plane manifolds yet retains throttle response/driveability of a dual
- Dual distributor hold-downs,No provisions for stock oil fill tube or stock exhaust-heated chokes.Will not fit under Corvette hood.Intake gaskets with 1.23" wide x 1.99" tall port
- Compatible with1957-86 SBC Chevy engine
Features
Information
- Best Choice - #7 Best Intake Manifold For Chevy 327
- Checked on 07/10/2024
- Based on 19 Reviews
Edelbrock 2701 Performer Intake Manifold
Highlighted Features
- Made of aluminum with a natural
- Dual plane intake style
- RPM range is idle to 5, 500
- Single carburetor without EGR
- Use on stock or original equipment standard
- Fit type: Vehicle Specific
Features
Information
- Best Choice - #8 Best Intake Manifold For Chevy 327
- Checked on 07/10/2024
- Based on 24 Reviews
Z Whip SBC INTAKE MANIFOLD BOLT KIT HIGH STRENGTH ZINC COATED 3/8-16 BOLTS Compatible with Chevrolet V8 Small Blocks 265 283 305 327 350 383 400 1955-1995 Gen I heads
Highlighted Features
- Compatible with all Chevy Small Block Oem and Most Aftermarket Intake Manifolds 265 283 305 307 327 350 383
- These are High Grade Zinc Coated Flange Bolts for Extra Clamping
- We are an AS9100D and ISO 9001:2015 Certified Manufacturer that produces aerospace parts for The Boeing Aircraft Company and The US Military. Parts we produce fly at 30,000 feet where
- When you purchase Z Whip Parts you will always get the highest quality for your vehicle that you rightfully
- Includes 12ea bolts.
Features
Information
- Best Choice - #9 Best Intake Manifold For Chevy 327
- Checked on 07/10/2024
- Based on 62 Reviews
FEL-PRO MS 90314-2 Intake Manifold Gasket Set
Highlighted Features
- DESIGNED FOR IMPERFECT SEALING SURFACES -- Engineered and manufactured specifically for the repair environment to help seal imperfect sealing
- SEALING TECHNOLOGIES -- Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your
- ENGINEERING EXPERTISE -- Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and
- REAL-WORLD TESTED -- Parts are tested on-vehicle and validated to ensure optimal performance on the
- EVERY PART FOR THE REPAIR -- Fel-Pro gasket sets include every part needed for the repair unless otherwise
Features
Information
- Best Choice - #10 Best Intake Manifold For Chevy 327
- Checked on 07/10/2024
- Based on 30 Reviews